View MIC2085-XBQS_5048577.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC2085/MIC2086
Single Channel Hot Swap Controllers
General Description
The MIC2085 and MIC2086 are single channel positive voltage hot swap controllers designed to allow the safe insertion of boards into live system backplanes. The MIC2085and MIC2086 are available in 16-pin and 20-pin QSOP packages, respectively. Using a few external components and by controlling the gate drive of an external N-Channel MOSFET device, the MIC2085/86 provide inrush current limiting and output voltage slew rate control in harsh, critical power supply environments. Additionally, a circuit breaker function will latch the output MOSFET off if the current limit threshold is exceeded for a programmed period of time. The devices' array of features provide a simplified yet robust solution for many network applications in meeting the power supply regulation requirements and affords protection of critical downstream devices and components. Data sheets and support documentation can be found on Micrel's web site at www.micrel.com.
* Operating temperature range -40C to 85C * Active current regulation limits inrush current independent of load capacitance * Programmable inrush current limiting * Analog foldback current limiting * Electronic circuit breaker * Dual-level overcurrent fault sensing * Fast response to short circuit conditions (< 1s) * Programmable output undervoltage detection * Undervoltage lockout protection * Power-on reset (MIC2085/86) and power-good (MIC2086) status outputs * /FAULT status output * Driver for SCR crowbar on overvoltage
Applications
* * * * * * RAID systems Cellular base stations LAN servers WAN servers InfiniBandTM Systems Industrial high side switching
Features
* MIC2085: Pin for pin functional equivalent to the LTC1642 * 2.3V to 16.5V supply voltage operation * Surge voltage protection to 33V
Typical Application
InfiniBand is a trademark of InfiniBand Trade Association PowerPAK is a trademark of Vishay Intertechnology, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
May 2006
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Ordering Information
Part Number Standard MIC2085-XBQS Pb-Free MIC2085-xYQS x = J, 95mV x = K, 150mV* x = L, 200mV* x = M, Off x = J, 95mV x = K, 150mV* x = L, 200mV* x = M, Off NA 16-Pin QSOP Fast Circuit Breaker Threshold Discharge Output Package
MIC2086-xBQS
MIC2086-xYQS
Yes
20-Pin QSOP
* Contact factory for availability.
Pin Configuration
MIC2085 16-Pin QSOP (QS)
MIC2086 20-Pin QSOP (QS)
Pin Description
Pin Number MIC2086 1 Pin Number MIC2085 1 Pin Name CRWBR Pin Function Overvoltage Timer and Crowbar Circuit Trigger: A capacitor connected to this pin, sets the timer duration for which an overvoltage condition will trigger an external crowbar circuit. This timer begins when the OV input rises above its threshold as an internal 45A current source charges the capacitor. Once the voltage reaches 470mV, the current increases to 1.5mA. Current Limit Response Timer: A capacitor connected to this pin defines the period of time (tOCSLOW) in which an overcurrent event must last to signal a fault condition and trip the circuit breaker. If no capacitor is connected, then tOCSLOW defaults to 5s. Power-On Reset Timer: A capacitor connected between this pin and ground sets the start-up delay (tSTART) and the power-on reset interval (tPOR). When VCC rises above the UVLO threshold, the capacitor connected to CPOR begins to charge. When the voltage at CPOR crosses 1.24V, the start-up threshold (VSTART), a start cycle is initiated if ON is asserted while capacitor CPOR is immediately discharged to ground. When the voltage at FB rises above VFB, capacitor CPOR begins to charge again. When the voltage at CPOR rises above the power-on reset delay threshold (VTH), the timer resets by pulling CPOR to ground, and /POR is deasserted. If CPOR = 0, then tSTART defaults to 20s.
2
2
CFILTER
3
3
CPOR
May 2006
2
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Pin Description (Cont.)
Pin Number MIC2086 4 Pin Number MIC2085 4 Pin Name ON Pin Function ON Input: Active high. The ON pin, an input to a Schmitt-triggered comparator used to enable/disable the controller, is compared to a VTH reference with 100mV of hysteresis. Once a logic high is applied to the ON pin (VON > 1.24V), a start-up sequence is initiated as the GATE pin starts ramping up towards its final operating voltage. When the ON pin receives a low logic signal (VON < 1.14V), the GATE pin is grounded and /FAULT is high if VCC is above the UVLO threshold. ON must be low for at least 20s in order to initiate a start-up sequence. Additionally, toggling the ON pin LOW to HIGH resets the circuit breaker. Power-On Reset Output: Open drain N-Channel device, active low. This pin remains asserted during start-up until a time period tPOR after the FB pin voltage rises above the power-good threshold (VFB). The timing capacitor CPOR determines tPOR. When an output undervoltage condition is detected at the FB pin, /POR is asserted for a minimum of one timing cycle, tPOR. The /POR pin has a weak pull-up to VCC Power-Good Output: Open drain N-Channel device, active high. When the voltage at the FB pin is lower than 1.24V, the PWRGD output is held low. When the voltage at the FB pin is higher than 1.24V, then PWRGD is asserted. A pullup resistor connected to this pin and to VCC will pull the output up to VCC. The PWRGD pin has a weak pull-up to VCC. Circuit Breaker Fault Status Output: Open drain N-Channel device, active low. The /FAULT pin is asserted when the circuit breaker trips due to an overcurrent condition. Also, this pin indicates undervoltage lockout and overvoltage fault conditions. The /FAULT pin has a weak pull-up to VCC. Power-Good Threshold Input: This input is internally compared to a 1.24V reference with 3mV of hysteresis. An external resistive divider may be used to set the voltage at this pin. If this input momentarily goes below 1.24V, then /POR is activated for one timing cycle, tPOR, indicating an output undervoltage condition. The /POR signal de-asserts one timing cycle after the FB pin exceeds the power-good threshold by 3mV. A 5s filter on this pin prevents glitches from inadvertently activating this signal. Ground Connection: Tie to analog ground OV Input: When the voltage on OV exceeds its trip threshold, the GATE pin is pulled low and the CRWBR timer starts. If OV remains above its threshold long enough for CRWBR to reach its trip threshold, the circuit breaker is tripped. Otherwise, the GATE pin begins to ramp up one POR timing cycle after OV drops below its trip threshold. Uncommitted Comparator's Open Drain Output. Comparator's Non-Inverting Input. Comparator's Inverting Input. Discharge Output: When the MIC2086 is turned off, a 550 internal resistor at this output allows the discharging of any load capacitance to ground. Reference Output: 1.24V nominal. Tie a 0.1F capacitor to ground to ensure stability. Gate Drive Output: Connects to the gate of an external N-Channel MOSFET. An internal clamp ensures that no more than 13V is applied between the GATE pin and the source of the external MOSFET. The GATE pin is immediately brought low when either the circuit breaker trips or an undervoltage lockout condition occurs.
5
5
/POR
6
NA
PWRGD
7
6
/FAULT
8
7
FB
9, 10 11
8 9
GND OV
12 13 14 15 16 17
10 11 12 Na 13 14
COMPOUT COMP+ COMPDIS REF GATE
May 2006
3
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Pin Description (Cont.)
Pin Number MIC2086 18 Pin Number MIC2085 15 Pin Name SENSE Pin Function Circuit Breaker Sense Input: A resistor between this pin and VCC sets the current limit threshold. Whenever the voltage across the sense resistor exceeds the slow trip current limit threshold (VTRIPSLOW), the GATE voltage is adjusted to ensure a constant load current. If VTRIPSLOW (48mV) is exceeded for longer than time period tOCSLOW, then the circuit breaker is tripped and the GATE pin is immediately pulled low. If the voltage across the sense resistor exceeds the fast trip circuit breaker threshold, VTRIPFAST, at any point due to fast, high amplitude power supply faults, then the GATE pin is immediately brought low without delay. To disable the circuit breaker, the SENSE and VCC pins can be tied together. The default VTRIPFAST for either device is 95mV. Other fast trip thresholds are available: 150mV, 200mV, or OFF (VTRIPFAST disabled). Please contact factory for availability of other options. 19, 20 16 VCC Positive Supply Input: 2.3V to 16.5V. The GATE pin is held low by an internal undervoltage lockout circuit until VCC exceeds a threshold of 2.18V.If VCC exceeds 16.5V, an internal shunt regulator protects the chip from VCC and SENSE pin voltages up to 33V.
May 2006
4
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Absolute Maximum Ratings(1)
(All voltages are referred to GND) Supply Voltage (VCC)....................................... -0.3V to 33V SENSE Pin ........................................... -0.3V to VCC + 0.3V GATE Pin ........................................................ -0.3V to 22V ON, DIS, /POR, PWRGD, /FAULT, COMP+, COMP-, COMPOUT......................... -0.3V to 20V CRWBR, FB, OV, REF...................................... -0.3V to 6V Maximum Currents Digital Output Pins ......................................................10mA (/POR, /FAUTL, PWRGD, COMPOUT) DIS Pin ........................................................................30mA EDS Rating Human Body Model ................................................. 2kV Machine Model ......................................................200V
Operating Ratings(2)
Supply voltage (VCC) .................................... 2.3V to +16.5V Operating Temperature Range ................... -40C to +85C Junction Temperature (TJ) ......................................... 125C Package Thermal Resistance R(JA) 16-pin QSOP ...................................................112C/W 20-pin QSOP .....................................................91C/W
Electrical Characteristics(3)
VCC = 5.0V; TA = 25C, unless otherwise noted. Bold indicates specifications over the full operating temperature range of -40C to +85C.
Symbol VCC ICC VUV VUVHYST VFB VFBHYST VOV VOV VOVHYST IOV VTH ICPOR ITIMER VCR VCR ICR Parameter Supply Voltage Supply Current Undervoltage Lockout Threshold UV Lockout Hysteresis FB (Power-Good) Threshold Voltage FB Hysteresis OV Pin Threshold Voltage OV Pin Threshold Voltage Line Regulation OV Pin Hysteresis OV Pin Current POR Delay and Overcurrent (CFILTER) Timer Threshold Power-On Reset Timer Current Current Limit /Overcurrent Timer Current (CFILTER) CRWBR Pin Threshold Voltage CRWBR Pin Threshold Voltage Line Regulation CRWBR Pin Current VCPOR, VCFILTER rising Timer on Timer off Timer on Timer off 2.3V < VCC < 16.5V 2.3V < VCC < 16.5V CRWBR On, VCRWBR = 0V CRWBR On, VCRWBR = 2.1V CRWBR Off, VCRWBR = 1.5V VTRIP = VCC = VSENSE 2.3V VCC 16.5V VTRIPSLOW VTRIPFAST x=J x=K x=L -60 1.19 -2.5 -30 445 1.24 -2.0 5 -20 2.5 470 4 -45 -1.5 3.3 48 95 150 200 OV pin rising 2.3V < VCC < 16.5V 1.19 FB rising 1.19 VCC rising VCC falling 2.05 1.85 Condition Min 2.3 1.6 2.18 2.0 180 1.24 3 1.24 5 3 0.2 1.29 -1.5 -15 495 15 -30 -1.0 55 110 1.29 15 1.29 Typ Max 16.5 2.5 2.28 2.10 Units V mA V V mV V mV mV mV mV A V A mA A mA mV A mA A mA mA mV mV mV mV
VTRIP
Circuit Breaker Trip Voltage (Current Limit Threshold)
40 80
May 2006
5
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Electrical Characteristics (Cont.)
Symbol VGS Parameter External Gate Drive Condition VGATE - VCC VCC < 3V 5V < VCC < 9V 9V < VCC <15.0V IGATE GATE Pin Pull-up Current Start cycle, VGATE > 0V VCC = 16.5V VCC = 2.3V /FAULT = 0, VGATE > 1V VCC = 16.5V VCC = 2.3V ON rising ON falling VON = VCC VCPOR rising IOUT = 1.6mA (PWRGD for MIC2086 only) /FAULT, /POR, PWRGD = GND (PWRGD FOR MIC2086 only) ILOAD = 0mA; CREF = 0.1 F 2.3V < VCC < 16.5V IOUT = 1mA VREF = 0V VCM = VREF VCM = VREF ON pin toggles from HI to LOW 100 -5 3 550 1000 1.21 -20 1.19 1.24 Min 4 11 4.5 -22 -20 25 12 1.19 1.09 Typ 8 12 21-VCC -16 -14 50 20 1.24 1.14 100 0.5 1.29 0.4 1.29 1.19 Max 9 13 13 -8 -8 Units V V V A A mA mA V V mV A V V A
IGATEOFF
GATE Pin Sink Current
VON VONHYST ION VSTART VOL IPULLUP
ON Pin Threshold Voltage ON Pin Hysteresis ON Pin Input Current Undervoltage Start-up Timer Threshold /FAULT, /POR, PWRGD Output Voltage Output Signal Pull-up Current /FAULT, /POR, PWRGD, COMPOUT Reference Output Voltage Reference Line Regulation Reference Load Regulation Reference Short-Circuit Current Comparator Offset Voltage Comparator Hysteresis Discharge Pin Resistance
VREF VLNR VLDR IRSC VCOS VCHYST RDIS
1.24 5 2.5 3.5
1.27 10 7.5 5
V mV mV mA mV mV
AC Electrical Characteristics(3)
Symbol tOCFAST Parameter Fast Overcurrent Sense to GATE Low Trip Time Slow Overcurrent Sense to GATE Low Trip Time ON Delay Filter FB Delay Filter Condition VCC = 5V VCC - VSENSE = 100mV CGATE = 10nF, See Figure 1 VCC = 5V VCC - VSENSE = 50mV CFILTER = 0, See Figure 1 Min Typ 1 Max Units s
tOCSLOW
5
s
tONDLY tFBDLY
Notes:
20 20
s s
1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Specification for packaged product only.
May 2006
6
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Timing Diagrams
VTRIPFAST 48mV
(VCC - VSENSE)
0
tOCSLOW 1V 1V
tOCFAST
VGATE
0 1.24V
CFILTER
0
Figure 1. Current Limit Response
1.24V FB 0 tPOR 1.24V CPOR 0
/POR
0
Figure 2. Power-On Reset Response
Figure 3. Power-On Start-Up Delay Timing
Current Limit Threshold (mV)
50
20
0
200
400
600
800
1000
FB Voltage (mV)
Figure 4. Foldback Current Limit Response
May 2006
7
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Typical Characteristics
4.0 SUPPLY CURRENT (mA) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 VCC = 2.3V VCC = 16.5V VCC = 5V
Supply Current vs. Temperature
Power-On Reset Timer (Off) Curren vs. Temperature
10 9 8 VCC = 16.5V 7 6 5 VCC = 5V 4 3 VCC = 2.3V 2 1 0 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
0.0 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
34 30 IT IMER ( A ) 26 22 18 14
Overcurrent Timer Current vs. Temperature
VCC = 16.5V
VCC = 5V
VCC = 2.3V
10 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
16 14 12 VGS (V) 10 8 6 4 2
External Gate Drive vs. Temperature
VCC = 5V
VCC = 16.5V
VCC = 2.3V
0 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
IC P OR (mA)
1.25 1.24 VTH (mV) 1.23 1.22 1.21
POR Delay/Overcurrent Timer Threshold vs. Temperature
VCC = 16.5V
VCC = 5V
VCC = 2.3V
1.20 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
May 2006
8
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Typical Characteristics (Cont.)
55 53 VTR IPS LOW (mV) 51 49 VCC = 5V 47 VCC = 16.5V VCC = 2.3V
Current Limit Threshold (Slow Trip) vs. Temperature
45 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
1.30 ON THRESHOLD (V)
ON Pin Threshol (Rising) d vs. Temperature
ON THRESHOLD (V)
1.20
ON Pin Threshol (Falling) d vs. Temperature
VCC = 2.3V
1.25
VCC = 16.5V
1.15
VCC = 5V 1.20
VCC = 2.3V
1.10
VCC = 16.5V VCC = 5V
1.15 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
1.05 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
COMPARATOR OFFSET VOLTAGE (V)
0.5 0.4 0.3 0.2 0.1
Comparator Offset Voltage vs. Temperature
VCC = 5V
VCC = 16.5V VCC = 2.3V
0.0 -40 -20 0 20 40 60 80 100 TEMPERATURE C) (
May 2006
9
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Test Circuit
IIN VIN 12V C4 0.47F R2 1% SW1 ON/OFF R3 1%
4 3 1
RSENSE 5%
2 4
Q1 Si7892DP (PowerPAKTM SO-8)
IOUT VOUT RLOAD CLOAD R4 1%
R1
19,20 18
VCC
SENSE GATE
17
ON FB MIC2086 /POR
5 8
C2 0.022F R5 1% Downstream Signal
SW2 DIS
R6
DIS CPOR
3
15
GND
9,10
CFILTER
2
R7
C3 0.047F
C4 0.047F C5 0.033F
Q2 ZTX788A
Q3 TCR22-4
Not all pins show for clarity.
R8
May 2006
10
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Functional Characteristics
May 2006
11
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Functional Characteristics (Cont.)
May 2006
12
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Functional Diagram
MIC2086 Block Diagram
May 2006
13
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
good" (See Figure 2 of "Timing Diagrams"). Active current regulation is employed to limit the inrush current transient response during start-up by regulating the load current at the programmed current limit value (See "Current Limiting and Dual-Level Circuit Breaker" section). The following equation is used to determine the nominal current limit value: ILIM = VTRIPSLOW 48mV = R SENSE R SENSE (2)
Functional Description
Hot Swap Insertion When circuit boards are inserted into live system backplanes and supply voltages, high inrush currents can result due to the charging of bulk capacitance that resides across the supply pins of the circuit board. This inrush current, although transient in nature, may be high enough to cause permanent damage to on-board components or may cause the system's supply voltages to go out of regulation during the transient period which may result in system failures. The MIC2085/86 acts as a controller for external N-Channel MOSFET devices in which the gate drive is controlled to provide inrush current limiting and output voltage slew rate control during hot plug insertions. Power Supply VCC is the supply input to the MIC2085/86 controller with a voltage range of 2.3V to 16.5V. The VCC input can with stand transient spikes up to 33V. In order to help suppress transients and ensure stability of the supply voltage, a capacitor of 1.0F to 10F from VCC to ground is recommended. Alternatively, a low pass filter, shown in the typical application circuit, can be used to eliminate high frequency oscillations as well as help suppress transient spikes. Start-Up Cycle When the voltage on the ON pin rises above its threshold of 1.24V, the MIC2085/86 first checks that its supply (VCC) is above the UVLO threshold. If it does check above, the device is enabled and an internal 2A current source begins charging capacitor CPOR to 1.24V to initiate a start-up sequence (i.e., start-up delay times out). Once the start-up delay (tSTART) elapses, CPOR is pulled immediately to ground and a 15A current source begins charging the GATE output to drive the external MOSFET that switches VIN to VOUT. The programmed start-up delay is calculated using the following equation:
t START = C POR x VTH ICPOR 0.62 x C POR (F ) (1)
where VTRIPSLOW is the current limit slow trip threshold found in the electrical table and RSENSE is the selected value that will set the desired current limit. There are two basic start-up modes for the MIC2085/86: 1)Start-up dominated by load capacitance and 2)start-up dominated by total gate capacitance. The magnitude of the inrush current delivered to the load will determine the dominant mode. If the inrush current is greater than the programmed current limit (ILIM), then load capacitance is dominant. Otherwise, gate capacitance is dominant. The expected inrush current may be calculated using the following equation: INRUSH IGATE x C LOAD C 15 x LOAD C GATE C GATE (3)
where IGATE is the GATE pin pull-up current, CLOAD is the load capacitance, and CGATE is the total GATE capacitance (CISS of the external MOSFET and any external capacitor connected from the MIC2085/86 GATE pin to ground).
Load Capacitance Dominated Start-Up In this case, the load capacitance, CLOAD, is large enough to cause the inrush current to exceed the programmed current limit but is less than the fast-trip threshold (or the fast-trip threshold is disabled, `M' option). During start-up under this condition, the load current is regulated at the programmed current limit value (ILIM) and held constant until the output voltage rises to its final value. The output slew rate and equivalent GATE voltage slew rate is computed by the following equation:
Output Voltage Slew Rate, dVOUT /dt = ILIM C LOAD (4)
where VTH, the POR delay threshold, is 1.24V, and ICPOR, the POR timer current, is 2A. As the GATE voltage continues ramping toward its final value (VCC + VGS) at a defined slew rate (See "Load Capacitance"/"Gate Capacitance Dominated Start-Up" sections), a second CPOR timing cycle begins if:1)/FAULT is high and 2)CFILTER is low (i.e., not an overvoltage, undervoltage lockout, or overcurrent state).This second timing cycle, tPOR, starts when the voltage at the FB pin exceeds its threshold (VFB) indicating that the output voltage is valid. The time period tPOR is equivalent to tSTART and sets the interval for the /POR to go Low-to-High after "power is
where ILIM is the programmed current limit value. Consequently, the value of CFILTER must be selected to ensure that the overcurrent response time, tOCSLOW, exceeds the time needed for the output to reach its final value. For example, given a MOSFET with an input capacitance CISS = CGATE =4700pF, CLOAD is 2200F, and ILIMIT is set to 6A with a 12Vinput, then the load capacitance dominates as determined by the calculated INRUSH > ILIM. Therefore, the output voltage slew rate determined from Equation 4 is:
May 2006
14
M9999-050406 (408) 955-1690
Micrel, Inc.
6A V = 2.73 2200F ms and the resulting tOCSLOW needed to achieve a 12V output is approximately 4.5ms. (See "Power-On Reset, Start-Up, and Overcurrent Timer Delays" section to calculate tOCSLOW.) Output Voltage Slew Rate, d VOUT /dt =
MIC2085/2086 a dual-level circuit breaker triggered via 48mV and 95mV current limit thresholds sensed across the VCC and SENSE pins. The first level of the circuit breaker functions as follows. Once the voltage sensed across these two pins exceeds 48mV, the overcurrent timer, its duration set by capacitor CFILTER, starts to ramp the voltage at CFILTER using a 2A constant current source. If the voltage at CFILTER reaches the overcurrent timer threshold (VTH) of 1.24V, then CFILTER immediately returns to ground as the circuit breaker trips and the GATE output is immediately shut down. For the second level, if the voltage sensed across VCC and SENSE exceeds 95mV at any time, the circuit breaker trips and the GATE shuts down immediately, bypassing the overcurrent timer period. To disable current limit and circuit breaker operation, tie the SENSE and VCC pins together and the CFILTER pin to ground.
GATE Capacitance Dominated Start-Up In this case, the value of the load capacitance relative to the GATE capacitance is small enough such that the load current during start-up never exceeds the current limit threshold as determined by Equation 3. The minimum value of CGATE that will ensure that the current limit is never exceeded is given by the equation below:
C GATE (min) = IGATE x C LOAD ILIM (5)
where CGATE is the summation of the MOSFET input capacitance (CISS) and the value of the external capacitor connected to the GATE pin of the MOSFET. Once CGATE is determined, use the following equation to determine the output slew rate for gate capacitance dominated start-up. dVOUT /dt (output ) = IGATE C GATE (6)
Table 1 depicts the output slew rate for various values of CGATE. CGATE 0.001F 0.01F 0.1F 1F
IGATE = 15A dVOUT/dt 15V/ms 1.5V/ms 0.150V/ms 0.015 F/ms
Output Undervoltage Detection The MIC2085/86 employ output undervoltage detection by monitoring the output voltage through a resistive divider connected at the FB pin. During turn on, while the voltage at the FB pin is below the threshold (VFB), the /POR pin is asserted low. Once the FB pin voltage crosses VFB, a 2A current source charges capacitor CPOR. Once the CPOR pin voltage reaches 1.24V, the time period tPOR elapses as the CPOR pin is pulled to ground and the /POR pin goes HIGH. If the voltage at FB drops below VFB for more than 10s, the/POR pin resets for at least one timing cycle defined by tPOR (see Applications Information for an example). Input Overvoltage Protection The MIC2085/86 monitors and detects overvoltage conditions in the event of excessive supply transients at the input. Whenever the overvoltage threshold (VOV) is exceeded at the OV pin, the GATE is pulled low and the output is shut off. The GATE will begin ramping one POR timing cycle after the OV pin voltage drops below its threshold. An external CRWBR circuit, as shown in the typical application diagram, provides a time period that an overvoltage condition must exceed in order to trip the circuit breaker. When the OV pin exceeds the overvoltage threshold (VOV), the CRWBR timer begins charging the CRWBR capacitor initially with a 45A current source.Once the voltage at CRWBR exceeds its threshold (VCR) of 0.47V, the CRWBR current immediately increases to 1.5mA and the circuit breaker is tripped, necessitating a device reset by toggling the ON pin LOW to HIGH. Power-On Reset, Start-Up, and Overcurrent TimerDelays The Power-On Reset delay, tPOR, is the time period for the /POR pin to go HIGH once the voltage at the FB pin exceeds the power-good threshold (VTH). A capacitor
15
M9999-050406 (408) 955-1690
Table 1. Output Slew Rate Selection for GATE Capacitance Dominated Start-Up
Current Limiting and Dual-Level Circuit Breaker Many applications will require that the inrush and steady state supply current be limited at a specific value in order to protect critical components within the system. Connecting a sense resistor between the VCC and SENSE pins sets the nominal current limit value of the MIC2085/86 and the current limit is calculated using Equation 2. However, the MIC2085/86 exhibits foldback current limit response. The foldback feature allows the nominal current limit threshold to vary from 24mVup to 48mV as the FB pin voltage increases or decreases. When FB is at 0V, the current limit threshold is 24mV and for FB 0.6V, the current limit threshold is the nominal 48mV.(See Figure 4 for Foldback Current Limit Response characteristic).The MIC2085/86 also features
May 2006
Micrel, Inc. connected to CPOR sets the interval, tPOR, and tPOR is equivalent to the start-up delay, tSTART (see Equation 1). A capacitor connected to CFILTER is used to set the timer which activates the circuit breaker during overcurrent conditions. When the voltage across the sense resistor exceeds the slow trip current limit threshold of 48mV, the overcurrent timer begins to charge for a period, tOCSLOW, determined by CFILTER. If no capacitor is used at CFILTER, then tOCSLOW defaults to 5s. If tOCSLOW elapses, then the circuit breaker is activated and the GATE output is immediately pulled to ground. The following equation is used to determine the overcurrent timer period, tOCSLOW. t OCSLOW = C FILTER x VTH I TIMER 0.062 x C FILTER (F ) (7)
MIC2085/2086 "power is good." For this example, the output value for which a 12V supply will signal "good" is 11V. Next, consider the tolerances of the input supply and FB threshold (VFB). For this example, the 12V supply varies 5%, thus the resulting output voltage may be as low as 11.4V and as high as 12.6V. Additionally, the FB threshold has 50mV tolerance and may be as low as1.19V and as high as 1.29V. Thus, to determine the values of the resistive divider network (R5 and R6) at the FB pin, shown in Figure 5, use the following iterative design procedure. 1) Choose R6 so as to limit the current through the divider to approximately 100A or less.
R6
VFB (MAX) 100
1.29V 12.9k 100
where VTH, the CFILTER timer threshold, is 1.24V and ITIMER, the overcurrent timer current, is 20A. Tables 2 and 3 provide a quick reference for several timer calculations using select standard value capacitors.
R6 is chosen as 13.3k 1% 2) Next, determine R5 using the output "good" voltage of 11V and the following equation: (R5 + R6 ) VOUT(Good) = VFB R6 (8)
CPOR 0.01F 0.02F 0.033F 0.05F 0.1F 0.33F
tPOR = tSTART 6ms 12ms 18.5ms 30ms 60ms 200ms
Using some basic algebra and simplifying Equation 8 to isolate R5, yields:
VOUT(Good) R5 = R6 VFB(MAX) - 1 (8.1)
Table 2. Selected Power-On Reset and Start-Up Delays
CFILTER 1800pF 4700pF 8200pF 0.01F 0.02F 0.033F 0.05F 0.1F 0.33F
tOCSLOW 100s 290s 500s 620s 1.2ms 2.0ms 3.0ms 6.2ms 20.7ms
where VFB(MAX) = 1.29V, VOUT(Good) = 11V, and R6 is13.3k. Substituting these values into Equation 8.1 now yields R5 = 100.11k. A standard 100k 1% is selected. Now, consider the 11.4V minimum output voltage, the lower tolerance for R6 and higher tolerance for R5, 13.17k and101k, respectively. With only 11.4V available, the voltage sensed at the FB pin exceeds VFB(MAX), thus the /POR and PWRGD (MIC2086) signals will transition from LOW to HIGH, indicating "power is good" given the worse case tolerances of this example.
Table 3. Selected Overcurrent Timer Delays
Input Overvoltage Protection The external CRWBR circuit shown in Figure 5 consists of capacitor C4, resistor R7, NPN transistor Q2, and SCR Q3.The capacitor establishes a time duration for an overvoltage condition to last before the circuit breaker trips. The CRWBR timer duration is approximated by the following equation:
t OVCR
(C4 x VCR )
ICR
0.01 x C4(F )
(9)
Application Information
Output Undervoltage Detection For output undervoltage detection, the first consideration is to establish the output voltage level that indicates
May 2006 16
where VCR, the CRWBR pin threshold, is 0.47V and ICR, the CRWBR pin current, is 45A during the timer period (see the CRWBR timer pin description for further description). A similar design approach as the previous undervoltage detection example is recommended for the
M9999-050406 (408) 955-1690
Micrel, Inc. overvoltage protection circuitry, resistors R2 and R3 in Figure 5. For input overvoltage protection, the first consideration is to establish the input voltage level that indicates an overvoltage triggering a sys-tem (output voltage) shut down. For this example, the input value for which a 12V supply will signal an "output shut down" is 13.2V (+10%). Similarly, from the previous example: 1) Choose R3 to satisfy 100A condition. R3 VOV (MIN) 100 1.19V 11.9k 100
MIC2085/2086 2) Thus, following the previous example and substituting R2 and R3 for R5 and R6, respectively, and 13.2V overvoltage for 11V output "good", the same formula yields R2 of 138.3k.The next highest standard 1% value is 140k. Now, consider the 12.6V maximum input voltage (VCC +5%), the higher tolerance for R3 and lower tolerance for R2, 13.84k and 138.60k, respectively. With a 12.6V input, the voltage sensed at the OV pin is below VOV(MIN), and the MIC2085/86will not indicate an overvoltage condition until VCC exceeds at least 13.2V.
R3 is chosen as 13.7k 1%.
Figure 5. Undervoltage/Overvoltage Circuit
May 2006
17
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 cycle. In Figure 6, the connection sense consisting of a logic-level discrete MOSFET and a few resistors allows for interrupt control from the processor or other signal controller to shut off the output of the MIC2085/86. R4 keeps the GATE of Q2 at VIN until the connectors are fully mated. A logic LOW at the/ON_OFF signal turns Q2 off and allows the ON pin to pull up above its threshold and initiate a start-up cycle. Applying a logic HIGH at the /ON_OFF signal will turn Q2 on and short the ON pin of the MIC2085/86 to ground which turns off the GATE output charge pump.
PCB Connection Sense There are several configuration options for the MIC2085/86'sON pin to detect if the PCB has been fully seated in the backplane before initiating a start-up cycle. In the typical applications circuit, the MIC2085/86 is mounted on the PCB with a resistive divider network connected to the ON pin. R2is connected to a short pin on the PCB edge connector. Until the connectors mate, the ON pin is held low which keeps the GATE output charge pump off. Once the connectors mate, the resistor network is pulled up to the input supply, 12V in this example, and the ON pin voltage exceeds its threshold (VON) of 1.24V and the MIC2085/86 initiates a start-up
Figure 6. PCB Connection Sense with ON/OFF Control
May 2006
18
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 GATE drive output will be shut down when VIN falls R1 below 1 + x 1.14V . In the example circuit (Figure R2 7), the rising UVLO threshold is set at approximately 11V and the falling UVLO threshold is established as 10.1V. The circuit consists of an external resistor divider at the ON pin that keeps the GATE output charge pump off until the voltage at the ON pin exceeds its threshold (VON) and after the start-up time relapses.
Higher UVLO Setting Once a PCB is inserted into a backplane (power supply), the internal UVLO circuit of the MIC2085/86 holds the GATE output charge pump off until VCC exceeds 2.18V. If VCC falls below 2V, the UVLO circuit pulls the GATE output to ground and clears the overvoltage and/or current limit faults. For a higher UVLO threshold, the circuit in Figure 7 can be used to delay the output MOSFET from switching on until the desired input voltage is achieved. The circuit allows the charge pump R1 to remain off until VIN exceeds 1 + x 1.24V . The R2
Figure 7. Higher UVLO Setting
May 2006
19
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 output is low) once the ON pin is deasserted. Figure 8(a) illustrates the use of the discharge feature with an optional resistor (R5) that can be used to provide added resistance in the output discharge path. For an even faster discharge response of capacitive loads, the configuration of Figure 8(b) can be utilized to apply a crowbar to ground through an external SCR (Q3) that is triggered when the DIS pin goes low which turns on the PNP transistor (Q2). See the different "Functional Characteristic" curves for a comparison of the discharge response configurations.
Fast Output Discharge for Capacitive Loads In many applications where a switch controller is turned off by either removing the PCB from the backplane or the ON pin is reset, capacitive loading will cause the output to retain voltage unless a `bleed' (low impedance) path is in place in order to discharge the capacitance. The MIC2086 is equipped with an internal MOSFET that allows the discharging of any load capacitance to ground through a 550 path. The discharge feature is configured by wiring the DIS pin to the output (source) of the external MOSFET and becomes active (DIS pin
Figure 8. MIC2086 Fast Discharge of Capacitive Load
May 2006
20
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 converter that steps down +12V to+3.3V for local bias. The pass transistor, Q1, isolates theMIC2182's input capacitance during module plug-in and allows the backplane to accommodate additional plug-in modules without affecting the other modules on the backplane. The two control input signals are VBxEn_L (active LOW) and a Local Power Enable (active HIGH). The MIC2085 in the circuit of Figure 10 performs a number of functions. The gate output of Q1 is enabled by the two bit input signal VBxEn_L, Local Power Enable = [0,1]. Also, the MIC2085 limits the drain current of Q1 to 7A, monitors VB_In for an overvoltage condition greater than 16V, and enables the MIC2182 DC/DC converter downstream to supply a local voltage rail. The uncommitted comparator is used to monitor VB_In for an undervoltage condition of less than 10V, indicated by a logic LOW at the comparator output (COMPOUT). COMPOUT may be used to control a downstream device such as another DC/DC converter. Additionally, the MIC2085 is configured for auto-retry upon an overcurrent fault condition by placing a diode (D1) between the /FAULT and ON pins of the controller.
Auto-Retry Upon Overcurrent Faults The MIC2085/86 can be configured for automatic restart after a fault condition. Placing a diode between the ON and/FAULT pins, as shown in Figure 9, will enable the auto-restart capability of the controller. When an application is configured for auto-retry, the overcurrent timer should be set to minimize the duty cycle of the overcurrent response to prevent thermal runaway of the power MOSFET. See "MOSFET Transient Thermal Issues" section for further detail. A limited duty cycle is achieved when the overcurrent timer duration (tOCSLOW) is much less than the start-up delay timer duration (tSTART) and is calculated using the following equation:
Auto - Retry Duty Cycle = t OCSLOW x 100% t START (10)
An InfiniBandTM Application Circuit The circuit in Figure 10 depicts a single 50W InfiniBandTM module using the MIC2085 controller. An InfiniBandTM backplane distributes bulk power to multiple plug-in modules that employ DC/DC converters for local supply requirements. The circuit in Figure 10 distributes 12V from the backplane to the MIC2182 DC/DC
Figure 9. Auto-Retry Configuration
May 2006
21
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Figure 10. A 50W InfiniBandTM Application
Sense Resistor Selection The MIC2085 and MIC2086 use a low-value sense resistor to measure the current flowing through the MOSFET switch (and therefore the load). This sense resistor is nominally valued at 48mV/ILOAD(CONT). To accommodate worst-case tolerances for both the sense resistor (allow 3% over time and temperature for a resistor with 1% initial tolerance) and still supply the maximum required steady-state load current, a slightly more detailed calculation must be used. The current limit threshold voltage (the "trip point") for theMIC2085/86 may be as low as 40mV, which would equate to a sense resistor value of 40mV/ILOAD(CONT). Carrying the numbers through for the case where the value of the sense resistor is 3% high yields:
R SENSE(MAX) = 40mV 38.8mV = (1.03 )(ILOAD(CONT) ILOAD(CONT)
As an example, if an output must carry a continuous 6Awithout nuisance trips occurring, Equation 11 yields:
R SENSE(MAX) =
38.8mV = 6.5m 6A
The next lowest standard value is 6.0mW. At the other set of tolerance extremes for the output in question:
ILOAD(CONT,MAX) =
56.7mV = 9.45A, 6.0m
almost 10A. Knowing this final datum, we can determine the necessary wattage of the sense resistor, using P = I2R, where I will be ILOAD(CONT, MAX), and R will be (0.97)(RSENSE(NOM)). These numbers yield the following: PMAX = (10A)2 (5.82m) =0.582W. In this example, a 1W sense resistor is sufficient.
)
(11)
Once the value of RSENSE has been chosen in this manner, it is good practice to check the maximum ILOAD(CONT) which the circuit may let through in the case of tolerance build-up in the opposite direction. Here, the worst-case maximum cur-rent is found using a 55mV trip voltage and a sense resistor that is 3% low in value. The resulting equation is:
MOSFET Selection Selecting the proper external MOSFET for use with theMIC2085/86 involves three straightforward tasks:
* * Choice of a MOSFET which meets minimum voltage requirements. Selection of a device to handle the maximum continuous current (steady-state thermal issues). Verify the selected part's ability to withstand any peak currents (transient thermal issues).
ILOAD(CONT,MAX) =
(0.97 )(R SENSE(NOM) )
55mV
=
56.7mV (12) R SENSE(NOM)
*
May 2006
22
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 * * The maximum ambient temperature in which the device will be required to operate.
MOSFET Voltage Requirements The first voltage requirement for the MOSFET is that the drain-source breakdown voltage of the MOSFET must be greater than VIN(MAX). For instance, a 16V input may reasonably be expected to see high-frequency transients as high as 24V.Therefore, the drain-source breakdown voltage of the MOSFET must be at least 25V. For ample safety margin and standard availability, the closest minimum value should be 30V. The second breakdown voltage criterion that must be met is a bit subtler than simple drain-source breakdown voltage. In MIC2085/86 applications, the gate of the external MOSFET is driven up to a maximum of 21V by the internal output MOSFET. At the same time, if the output of the external MOSFET (its source) is suddenly subjected to a short, the gate-source voltage will go to (21V - 0V) = 21V. Since most power MOSFETs generally have a maximum gate-source breakdown of 20V or less, the use of a Zener clamp is recommended in applications with VCC 8V. A Zener diode with 10V to 12V rating is recommended as shown in Figure11. At the present time, most power MOSFETs with a 20V gatesource voltage rating have a 30V drain-source breakdown rating or higher. As a general tip, choose surfacemount devices with a drain-source rating of 30V or more as a starting point. Finally, the external gate drive of the MIC2085/86 requires a low-voltage logic level MOSFET when operating at voltage slower than 3V. There are 2.5V logic-level MOSFETs avail-able. Please see Table 4, "MOSFET and Sense Resistor Vendors" for suggested manufacturers. MOSFET Steady-State Thermal Issues The selection of a MOSFET to meet the maximum continuous current is a fairly straightforward exercise. First, arm yourself with the following data:
* * The value of ILOAD(CONT, MAX.) for the output in question (see "Sense Resistor Selection"). The manufacturer's data sheet for the candidate MOSFET.
Any knowledge you can get about the heat sinking available to the device (e.g., can heat be dissipated into the ground plane or power plane, if using a surface-mount part? Is any airflow available?). The data sheet will almost always give a value of on resistance given for the MOSFET at a gate-source voltage of 4.5V, and another value at a gate-source voltage of 10V. As a first approximation, add the two values together and divide by two to get the onresistance of the part with 8V of enhancement. Call this value RON. Since a heavily enhanced MOSFET acts as an ohmic (resistive) device, almost all that's required to determine steady-state power dissipation is to calculate I2R.The one addendum to this is that MOSFETs have a slight increase in RON with increasing die temperature. A good approximation for this value is 0.5% increase in RON per C rise in junction temperature above the point at which RON was initially specified by the manufacturer. For instance, if the selected MOSFET has a calculated RON of 10m at a TJ = 25C, and the actual junction temperature ends up at 110C, a good first cut at the operating value for RON would be: RON 10m[1 + (110 - 25)(0.005)] 14.3m The final step is to make sure that the heat sinking available to the MOSFET is capable of dissipating at least as much power (rated in C/W) as that with which the MOSFET's performance was specified by the manufacturer. Here are a few practical tips: 1. The heat from a surface-mount device such a san SO-8 MOSFET flows almost entirely out of the drain leads. If the drain leads can be soldered down to one square inch or more, the copper will act as the heat sink for the part. This copper must be on the same layer of the board as the MOSFET drain.
May 2006
23
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Figure 11. Zener Clamped MOSFET GATE
2. Airflow works. Even a few LFM (linear feet per minute) of air will cool a MOSFET down substantially. If you can, position the MOSFET(s) near the inlet of a power supply's fan, or the outlet of a processor's cooling fan. 3. The best test of a surface-mount MOSFET for an application (assuming the above tips show it to be a likely fit) is an empirical one. Check the MOSFET's temperature in the actual layout of the expected final circuit, at full operating current. The use of a thermocouple on the drain leads, or infrared pyrometer on the package, will then give a reasonable idea of the device's junction temperature.
MOSFET Transient Thermal Issues Having chosen a MOSFET that will withstand the imposed voltage stresses, and the worse case continuous I2R power dissipation which it will see, it remains only to verify the MOSFET's ability to handle short-term overload power dissipation without overheating. A MOSFET can handle a much higher pulsed power without damage than its continuous dissipation ratings would imply. The reason for this is that, like everything else, thermal devices (silicon die, lead frames, etc.) have thermal inertia. In terms related directly to the specification and use of power MOSFETs, this is known as "transient thermal impedance," or Z(J-A). Almost all power MOSFET data sheets give a Transient Thermal Impedance Curve. For example, take the following case: VIN = 12V, tOCSLOW
May 2006 24
has been set to 100msec, ILOAD(CONT. MAX) is 2.5A, the slow-trip threshold is 48mVnominal, and the fast-trip threshold is 95mV. If the output is accidentally connected to a 3 load, the output current from the MOSFET will be regulated to 2.5A for 100ms (tOCSLOW) before the part trips. During that time, the dissipation in the MOSFET is given by: P=ExI EMOSFET = [12V-(2.5A)(3)]=4.5V PMOSFET = (4.5V x 2.5A) = 11.25W for 100msec. At first glance, it would appear that a really hefty MOSFET is required to withstand this sort of fault condition. This is where the transient thermal impedance curves become very useful. Figure 12 shows the curve for the Vishay (Siliconix) Si4410DY, a commonly used SO-8 power MOSFET. Taking the simplest case first, we'll assume that once a fault event such as the one in question occurs, it will be a long time - 10 minutes or more - before the fault is isolated and the channel is reset. In such a case, we can approximate this as a "single pulse" event, that is to say, there's no significant duty cycle. Then, reading up from the X-axis at the point where "Square Wave Pulse Duration" is equal to 0.1sec (=100msec), we see that the Z(J-A) of this MOSFET to a highly infrequent event of this duration is only 8% of its continuous R(J-A). This particular part is specified as having an R(J-A) of 50C/W for intervals of 10 seconds or less. Thus: Assume TA = 55C maximum, 1 square inch of copper at the drain leads, no airflow. Recalling from our previous approximation hint, the part
M9999-050406 (408) 955-1690
Micrel, Inc. has an RON of (0.0335/2) = 17m at 25C. Assume it has been carrying just about 2.5A for some time. When performing this calculation, be sure to use the highest anticipated ambient temperature (TA(MAX)) in which the MOSFET will be operating as the starting temperature, and find the operating junction temperature increase (TJ) from that point. Then, as shown next, the final junction temperature is found by adding TA(MAX) and TJ. Since this is not a closed-form equation, getting a close approximation may take one or two iterations, but it's not a hard calculation to perform, and tends to converge quickly. Then the starting (steady-state) TJ is: TJ TA(MAX) + TJ TA(MAX) + [RON + (TA(MAX) -TA)(0.005/C) (RON)] x I2 x R(J-A) TJ 55C + [17m + (55C-25C)(0.005) (17m)] x (2.5A)2 x (50C/W) TJ (55C + (0.122W)(50C/W) 61.1C
MIC2085/2086 Iterate the calculation once to see if this value is within a few percent of the expected final value. For this iteration we will start with TJ equal to the already calculated value of 61.1C: TJ TA + [17m + (61.1C-25C)(0.005)(17m)] x (2.5A)2 x (50C/W) TJ ( 55C + (0.125W)(50C/W) 61.27C So our original approximation of 61.1C was very close to the correct value. We will use TJ = 61C. Finally, add (11.25W)(50C/W)(0.08) = 45C to the steady-state TJ to get TJ(TRANSIENT MAX.) = 106C. This is an acceptable maximum junction temperature for this part.
Figure 12. Transient Thermal Impedance
May 2006
25
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 swap applications will require load currents of several amperes. Therefore, the power (VCC and Return) trace widths (W) need to be wide enough to allow the current to flow while the rise in temperature for a given copper plate (e.g., 1 oz. or 2 oz.) is kept to a maximum of 10C ~ 25C. Also, these traces should be as short as possible in order to minimize the IR drops between the input and the load. For a starting point, there are many trace width calculation tools available on the web such as the following link: http://www.aracnet.com/cgi-usr/gpatrick/trace.pl Finally, plated-through vias are utilized to make circuit connections to the power and ground planes. The trace connections with indicated vias should follow the example shown for the GND pin connection in Figure 13.
PCB Layout Considerations Because of the low values of the sense resistors used with theMIC2085/86 controllers, special attention to the layout must be used in order for the device's circuit breaker function to operate properly. Specifically, the use of a 4-wire Kelvin connection to measure the voltage across RSENSE is highly recommended. Kelvin sensing is simply a means of making sure that any voltage drops in the power traces connecting to the resistors does not get picked up by the traces themselves. Additionally, these Kelvin connections should be isolated from all other signal traces to avoid introducing noise onto these sensitive nodes. Figure 13 illustrates a recommended, multi-layer layout for the RSENSE, Power MOSFET, timer(s), overvoltage and feedback network connections. The feed-back and overvoltage resistive networks are selected for a12V application (from Figure 5). Many hot
Figure 13. Recommended PCB Layout for Sense Resistor, Power MOSFET, and Feedback/Overvoltage Network
May 2006
26
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086 recommended trace for the MOSFET Gate of Figure 13 must be redirected when using MOSFETs packaged in this style. Contact the device manufacturer for package information.
MOSFET and Sense Resistor Vendors Device types and manufacturer contact information for power MOSFETs and sense resistors is provided in Table 4. Some of the recommended MOSFETs include a metal heat sink on the bottom side of the package. The MOSFET Vendors
Vishay (Siliconix)
Key MOSFET Type(s)
Si4420DY (SO-8 package) Si4442DY (SO-8 package) Si3442DV (SO-8 package) Si7860DP (PowerPAKTM SO-8) Si7892DP (PowerPAKTM SO-8) Si7884DP (PowerPAKTM SO-8) SUB60N06-18 (TO-263) SUB70N04-10 (TO-263) IRF7413 (SO-8 package) IRF7457 (SO-8 package) IRF7822 (SO-8 package) IRLBA1304 (Super220TM) FDS6680A (SO-8 package) FDS6690A (SO-8 package) PH3230 (SOT669-LFPAK) HAT2099H (LFPAK)
*Applications
IOUT 10A IOUT = 10A - 15A, VCC 5V IOUT 3A, VCC 5V IOUT 12A IOUT 15A IOUT 15A IOUT 20A, VCC 5V IOUT 20A, VCC 5V IOUT 10A IOUT 10A IOUT = 10A - 15A, VCC 5V IOUT 20A, VCC 5V IOUT 10A IOUT 10A, VCC 5V IOUT 20A IOUT 20A
Contact Information
www.siliconix.com (203) 452-5664
International Rectifier
www.irf.com (310) 322-3331
Fairchild Semiconductor Philips Hitachi
www.fairchildsemi.com (207) 775-8100 www.philips.com www.halsp.hitachi.com (408) 433-1990
* These devices are not limited to these conditions in many cases, but these conditions are provided as a helpful reference for customer applications
Resistor Vendors
Vishay (Dale) IRC
Sense Resistors
"WSL" Series "OARS" Series "LR" Series (second source to "WSL")
Contact Information
www.vishay.com/docswsl_30100.pdf (203) 452-5664 www.irctt.com/pdf_files/OARS.pdf www.irctt.com/pdf_files/LRS.pdf (828) 264-8861
Table 4. MOSFET and Sense Resistor Vendors
May 2006
27
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
Package Information
16-Pin QSOP (QS)
May 2006
28
M9999-050406 (408) 955-1690
Micrel, Inc.
MIC2085/2086
20-Pin QSOP (QS)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated.
May 2006
29
M9999-050406 (408) 955-1690

▲Up To Search▲

Price & Availability of MIC2085-XBQS

	To Download MIC2085-XBQS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .